Publications List

1. "Conducting the Failure Examination," ASM .Metals Eng. Q, Vol. 15, May 1975, pp. 31-36.

2. "Analyzing Ductile and Brittle Failures," ASM Metals Eng. Q., Vol. 16, August 1976, pp. 31-59.

3. "Macroscopic Examination Procedures," Metallography in Failure Analysis, Plenum Press, NY, 1978, pp. 33-63.

4. "A Metallographic Study of Factors Influencing the Toughness of Cermets (70% Alumina - 30% TiC) Inserts," Productivity Improvements Through New Tools and Applications, Proc. Soc. Carbide and Tool Engs., 1979, pp. 153-188 (R.W. Hinton, co-author).

5. "Inclusion Measurement," Metallography as a Quality Control Tool, Plenum Press, NY, 1980, pp. 1-88.

6. Co-editor, Microstructural Science, Vol. 8, Elsevier North-Holland, NY, 1980, 400 pgs.

7. "Etching Techniques for Image Analysis," Microstructural Science, Vol. 9, Elsevier North-Holland, NY, 1981, pp. 137-154.

8. "Automating the JK Inclusion Analysis," Microstructural Science, Vol. 10, Elsevier North-Holland, NY, 1982, pp. 277-290 (J.F. Golden, co-author).

9. "Grain Size Measurement," Practical Applications of Quantitative Metallography, ASTM STP 839, ASTM, Phila., 1984, pp. 85-131.

10. "Measurement of the Interlamellar Spacing of Pearlite," Metallography, Vol. 17, February 1984, pp. 1-17 (A. Roósz, co-author).

11. Metallography: Principles and Practice, McGraw-Hill Book Co., NY, 1984, ASM Intl, 1999, 752 pgs.

12. "Tint Etching," Metal Progress, Vol. 127, March 1985, pp. 31-33, 36-38, 41, and front cover.

13. Editor, Corrosion, Microstructure & Metallography, Microstructural Science, Vol. 12, Proc. 16th Annual IMS Technical Meeting, Calgary, ASM and IMS, Metals Park, OH, 1985, 590 pgs.

14. Co-editor, "Metallography," Chapter 35 in Metals Handbook Desk Edition, ASM, Metals Park, OH, 1985, pp. 35-1 to 35-60.

15. "Measurement of Microstructure," Metals Handbook Desk Edition, ASM, Metals Park, OH, 1985, pp. 35-16 to 35-20.

16. "Typical Microstructures of Iron-Based Alloys," Metals Handbook Desk Edition, ASM, Metals Park, OH, 1985, pp. 35-37 to 35-47.

17. "Comparative Analysis of Stereological Methods for Determining the Distribution of True Interlamellar Spacing," 8th European Congress on Electron Microscopy, Budapest, 1984, pp. 771-772 (with T. Reti and A. Roosz).

18. Editor, Corrosion, Failure Analysis, and Metallography, Microstructural Science, Vol. 13, Proc. 17th Annual IMS Technical Meeting, Phila., IMS and ASM, Metals Park, OH, 1986, 599 pgs.19. "Optical Microscopy," Metallography and Microstructures, Vol. 9, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1985, pp. 71-88.

20. "Tool Steels," Metallography and Microstructures, Vol. 9, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1985, pp. 256-272.

21. "Wrought Stainless Steels," Metallography and Microstructures, Vol. 9, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1985, pp. 279-296.

22. "Wrought Heat Resistant Alloys," Metallography and Microstructures, Vol. 9, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1985, pp. 305-329.

23. "Magnetic and Electrical Materials," Metallography and Microstructures, Vol. 9, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1985, pp. 531-549.

24. "Color Etching," Metallography and Microstructures, Vol. 9, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1985, pp. 139-142, 156.

25. "Microstructures of Carbon and Alloy Steels," Metallography and Microstructures, Vol. 9, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1985, pp. 177-179.

26. "Image Analysis," Materials Characterization, Vol. 10, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1986, pp. 309-322.

27. "Failures of Tools and Dies," Failure Analysis and Prevention, Vol. 11, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1986, pp. 563-585.

28. "Failures of Locomotive Axles," Failure Analysis and Prevention, Vol. 11, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1986, pp. 715-727.

29. "The Use of Light Microscopy in Failure Analysis," Microscopy and Fractography in Failure Analysis, IMS, Virginia Tech Printing Dept., 1986, pp. III-1 to III-32.

30. Editor, Welding, Failure Analysis, and Metallography, Microstructural Science, Vol. 14, Proc. 18th Annual IMS Technical Meeting, Denver, IMS and ASM, Metals Park, OH, 1987, 598 pgs.

31. Editor, Applied Metallography, Van Nostrand Reinhold Co., Inc., NY, 1986, 301 pgs.

32. "Phase Identification by Selective Etching," Applied Metallography, Van Nostrand Reinhold Publishing Co., Inc., NY, 1986, pp. 1-19.

33. "The SEM as a Metallographic Tool," Applied Metallography, Van Nostrand Reinhold Co., Inc., NY, 1986, pp. 139-170.

34. "Visual Examination and Light Microscopy," Fractography, Vol. 12, 9th ed., Metals Handbook, ASM, Metals Park, OH, 1987, pp. 91-165.

35. "Measurement of Extremely Low Inclusion Contents by Image Analysis," Effect of Steel Manufacturing Processes on the Quality of Bearing Steels, ASTM STP 987, ASTM, Phila., 1988, pp. 226-249.

36. Co-editor, MiCon 86: Optimization of Processing, Properties, and Service Performance Through Microstructural Control, ASTM STP 979, ASTM, Phila., 1988, 315 pgs.

37. Editor, Field Metallography, Failure Analysis, and Metallography, Microstructural Science, Vol. 15, Proc. 19th Annual IMS Technical Meeting, Boston, IMS and ASM, Metals Park, OH, 1987, 584 pgs.

38. "Influence of Magnification on Feature-Specific Image Analysis Measurements," Metallography, Vol. 21, No. 3, 1988, pp. 327-345.

39. "Results of an ASTM E-4 Round-Robin on the Precision and Bias of Measurements of Microindentation Hardness Impressions," Factors That Affect the Precision of Mechanical Tests, ASTM STP 1025, ASTM, Phila., 1989, pp. 3-39.

40. "Operator Errors in the Measurement of Microindentation Hardness," Accreditation Practices for Inspections, Tests, and Laboratories, ASTM STP 1057, ASTM, Phila., 1989, pp. 47-77.

41. "Characterization of Inclusions in a Laboratory Heat of AISI 303 Stainless Steel," Inclusions and Their Influence on Material Behavior, ASM International, Metals Park, OH, 1988, pp. 49-64.

42. "Imaging by Light Optical Microscopy," Imaging of Materials, Oxford University Press, Oxford, 1991, pp. 3-53.

43. Editor, Metallography of Advanced Materials, Vol. 16, Microstructural Science, Proc. 20th Annual IMS Technical Meeting, Monterey, IMS and ASM International, Metals Park, OH, 1988, 598 pgs.

44. "Advances in Microstructural Imaging. Directions in Metallography," Standardization News, Vol. 16, November 1988, pp. 50-57, and Front Cover.

45. "The Metallography of Stainless Steels," Journal of Metals, Vol. 41, March 1989, pp. 6-11.

46. Editor, Image Analysis and Metallography, Vol. 17, Microstructural Science, Proc. 21st Annual IMS Technical Meeting, Toronto, IMS and ASM International, Metals Park, OH, 1989, 532 pgs.

47. "Video Microscopy: Its Impact on the Sciences," Microscope Technology & News, Vol. 1, No. 6, June 1989, pp.4 and 5.

48. "Image Analysis: A Short History," Slip Lines, Vol. 16, June 15, 1989, pp. 1 and 2.

49. "Metallography: Entering the 1990s," Advanced Materials & Processes, Vol. 136, November 1989, pp. 6-8.

50. "Metallographic Trends," Advanced Materials & Processes, Vol. 137, January 1990, pp. 71 and 90.

51. "Computer-Aided Microstructural Analysis of Specialty Steels," Materials Characterization, Special Issue 5, Vol. 27, No. 4, December 1991, pp. 241-260.

52. "Embrittlement of Steels," Properties and Selection: Irons, Steels, and High-Performance Alloys, Vol. 1, 10th edition, Metals Handbook, ASM International, Materials Park, OH, 1990, pp. 689-736.

53. "Evaluating Clustering of Second-Phase Particles," MiCon 90: Advances in Video Technology for Microstructural Control, ASTM STP 1094, G.F. Vander Voort, ed., ASTM, Philadelphia, 1991, pp. 242-267.

54. Editor, MiCon 90: Advances in Video Technology for Microstructural Control, STP 1094, ASTM, Philadelphia, 1991, 387 pgs.

55. "ASTM and Metallography," Slip Lines, Vol. 17, No. 2, June 15, 1990, pp. 1 and 4.

56. "Progress in Metallographic Test Standards," Advanced Materials & Processes, Vol. 138, November 1990, pp. 30-33, 36-38.

57. Editor, Computer-Aided Microscopy and Metallography, Microstructural Science, Vol. 18, Proc. 22nd Annual IMS Technical Meeting, Charlotte, NC, IMS and ASM International, Materials Park, OH, 1990, 533 pgs.

58. "Nonmetallic Inclusions and ASTM Committee E-4," Standardization News, Vol. 19, May 1991, pp. 28-37 (with R.K. Wilson).

59. "Committee E-4 and Grain Size Measurements: 75 Years of Progress," Standardization News, Vol. 19, May 1991, pp. 42-47.

60. "75 Years of Metallography. The ASTM Committee E-4 Perspective," Standardization News, Vol. 19, May 1991, pp. 58-77.

61. Editor, Atlas of Time-Temperature Diagrams for Irons and Steels, ASM International, Materials Park, OH, 1991, 807 pgs.

62. "Examination of Some Grain Size Measurement Problems," Metallography: Past, Present and Future, ASTM STP 1165, ASTM, Philadelphia, 1993, pp. 266-294.

63. "The History of ASTM Committee E-4 on Metallography," Metallography: Past, Present and Future, ASTM STP 1165, ASTM, Philadelphia, 1993,pp. 3-79.

64. Editor, Atlas of Time-Temperature Diagrams for Nonferrous Alloys, ASM International, Materials Park, OH, 1991, 300 pgs.

65. Co-editor, Failure Analysis: From Large Structures to Small Components, Materials Characterization, Vol. 26, No. 4, June 1991, pp. 199-323.

66. Editor, Computer-aided Materials Characterization, Materials Characterization, Vol. 27, No. 4, December 1991, pp. 183-295.

67. "Comments on `Grain Size Measurements Using the Point-Sampled Intercept Technique'," Scripta Met. et Matl., Vol. 26, No. 10, March 15, 1992, pp. 1655-1660 (A.M. Gokhale co-author)

68. "Comments on `Measurement of Grain Size Using the Circle Intercept Method'," Scripta Met. et Matl., Vol. 26, No. 11, June 1, 1992, pp. 1785-1790.

69. "Image Analysis Measurements of Duplex Grain Structures," (J.J. Friel, co-author), Materials Characterization, Vol. 29, No. 3, October 1992, pp. 293-312.

70. "Safety in the Metallographic Laboratory," Standardization News, Vol. 20, May 1992, pp. 34-39 (R.C. Nester co-author).

71. "A Note on Metallographic Techniques for Iron Meteorites," Material Characterization, Vol. 29, No. 2, September 1992, pp. 223-241.

72. "Application of Quantitative Microscopy to Specialty Metals," Proc of the 50th Annual EMSA Meeting, Vol. 2, San Francisco Press, San Francisco, 1992, pp. 1606-1607.

73. "Polishing with Colloidal Silica," Structure, Struers Tech A/S, Copenhagen, No. 26, 1992, pp. 3-11 (micrograph on front cover and inside front cover also).

74. Co-editor, Metallography, History, and the Fine Arts, Special Issue of Materials Characterization, Vol. 29, No. 2, September 1992, pp. 65-270.

75. Preface, "Cyril Stanley Smith," Materials Characterization, Vol. 29, No. 2, September 1992, pp. 65-66.

76. "Charles S. Barrett Receives the IMS Sorby Award," Slip Lines, Vol. 19, No. 3, 15 September 1992, p. 2.

77. "Obituary: Cyril Stanley Smith," Slip Lines, Vol. 19, No. 3, 15 September 1992, p. 5.

78. "Color Metallography of Iron Meteorites," Kodak Tech Bits, Issue No. 2, 1992, pp. 11-19.

79. Co-editor, Metallography: Past, Present and Future (75th Anniversary Volume), ASTM STP 1165, ASTM, Philadelphia, 1993, 453 pgs.

80. "User Comments on the New Etch of Zhang and Guo," Materials Characterization, Vol. 30, No. 4, June 1993, pp. 303-305 (J.R. Kilpatrick, co-author).

81. "Wetting Agents in Metallography," Materials Characterization, Vol. 35, No. 2, September 1995, pp. 135-137.

82. "Preparation of High Alloy Martensitic Steels," Structure, No. 27, Struers Tech A/S, January 1994, pp. 3-8 (J.A. Lesher co-author).

83. "Image Analysis and the Video Revolution," ASM News, Vol. 24, no.6, June 1993, p.3.

84. "Precision and Reproducibility of Quantitative Measurements," Quantitative Microscopy and Image Analysis, ASM International, Materials Park, OH April 1994, pps. 21-34.

85. "Statistical Aspects of Microstructural Measurements," Microscopy: Materials & Techniques, Institute of Metals and Materials Australasia, 21-22 Sept. 1993, pp. 1-6.

86. "Further Comments on "Measurement of Grain Size Using the Circle Intercept Method," Scripta Metallurgica et Materialia, Vol. 29, Dec. 15, 1993, pp. 1655-1660.

87. "Raimond Castaing Receives 1993 Sorby Award," Slip Lines, Vol. 20, No. 3, Sept. 15, 1993, p. 3.

88. "Notes From the Traveling Metallographer," Slip Lines, Vol. 20, No. 4, December 15, 1993, pp. 4-5.

89. "ASTM Standards for Quantitative Metallography," EUROMAT 94, Conference Proc., 1994, Vol. 1, pp. 69-79.

90. "Microstructural Characterization of Custom Age 625 PLUS Alloy," Superalloys 718, 625, 706 and Various Derivatives, E.A. Loria (ed.), The Minerals, Metals & Materials Society, Warrendale, PA 1994, pp. 489-498 (J.W. Bowman and R.B. Frank co-authors).

91. Editor, Special Issue on Memory Metals, Materials Characterization, Vol. 32, April 1994, pp. 139-235.

92. Editor, Special Issue on Computer Modeling and Microstructures, Materials Characterization, Vol. 32, June 1994, pp. 239-298.

93. "Peer Review of the Three Mile Island Unit 2 Vessel Investigation Project Metallurgical Examinations," NUREG/CR-6183, ANL-94/3, U.S. Nuclear Regulatory Commission, July 1994 (with R.W. Bohl and R.G. Gaydos).

94. "A Layman's View of Plasma-Spray Coating Metallography," Structure, No. 28, 1995, pp. 8-13.

95. "Pickering Receives Sorby Award," Slip Lines, Vol. 21, No. 3, 15 Sept. 1994, p.1.

96. "1994 IMS/ASM Distinguished Lecturer," Slip Lines, Vol. 21, No. 3, 15 Sept. 1994, p.3.

97. Editor, Special Issue on Metallography and Failure Analysis, Materials Characterization, Vol. 33, No. 3, October 1994.

98. Editor, Special Issue on Microstructural Characterization of Lightweight Structural Materials for Transportation, Materials Characterization, Vol. 34, No. 4, June 1995.

99. "Thermal Exposure Assessment by Quantitative Microscopy and Selective Etching," MC 95, International Metallographic Conference, 10-12 May 1995, Colmar, France, Conf. Proc., ASMI, Materials Park, OH, 1996, pp. 311-316.

100. "Progress in Characterizing Materials Using Image Analysis," Developments in Materials Characterization Technologies, ASMI, Materials Park, OH, 1996, pp. 23-32.

101. Editor, Developments in Materials Characterization Technologies, ASMI, Materials Park, OH 1996 (J.J. Friel, co-editor).

102. "Metallography of Stainless Steel and High Temperature Alloy Fasteners," Structure, No. 30, 1997, pp 14-20.

103. "Metallographic Assessment of the Thermal Exposure to the Three Mile Island Unit 2 Reactor Lower Head," Materials Characterization, Vol. 36, No. 4/5, April/June 1996, pp291-307.

104. Editor, Special Double Issue on International Metallography Conference MC 95, Colmar, France, Materials Characterization, Vol. 36, No. 4/5, April/June 1996.

108. "Use of Failure Analysis in Materials Selection," ASM Metals Handbook, Vol. 20, Materials Selection and Design, ASM International, Materials Park, OH, 1997, pp. 322-328.

109. "Is it Real or is it an Artifact?," Slip Lines, Vol. 24, No. 1, March 1996, pp. 1 and 2 (also printed in Special Convention issue of Slip Lines, June 1996).

110. "Assessing the Thermal Exposure to the Three Mile Island Unit 2 Reactor Lower Head by Metallographic Methods," Proceedings, Second International Seminar and Exhibition on Materialography, The Institute of Metals and Materials Australasia Ltd., Melbourne, 1996, pp. 3-8.

111. “The SEM as a Metallographic Tool,” Acta Microscopica, Proc. of the 5th Brazilian Conference on Microscopy of Materials, Brazilian Society for Electron Microscopy, 1996, pp. 48-51.

112. “Phase Identification by Selective Etching,” Acta Microscopica, Proc. of the 5th Brazilian Conference on Microscopy of Materials, Brazilian Society for Electron Microscopy, 1996, pp. 52-55.

113. “ASTM Standards for Quantitative Metallography,” Proceedings of Microscopy Society of Southern Africa, Vol. 26, 1996, p.8.

114. “Inclusion Ratings: Past, Present and Future,” Fifth International Symposium on Bearing Steels: Into the 21st Century, ASTM STP 1327, ASTM, West Conshocken, PA, 1998, pp. 13-26.

115. “Measuring Inclusion Content by ASTM E 1245,” Proc. Fifth International Conference on Clean Steel, 2-4 June, 1997, Balatonfüred, Hungary, Vol. 2, pp.58-67.

116.”Metallographic Characterization of Pyromet® 718 Alloy Fasteners,” Fourth International Special Emphasis Symposium on Superalloys 718, 625, 706 and Derivatives, Pittsburgh, PA 15-19 June 1997, pp. 825-834.

117. Editor, Special Issue on Novel Deformation Processes, Materials Characterization, Vol. 37, No. 5, November 1996.

118. “ASTM Standards for Quality Control,” Microstructural Science, Vol. 24, IMS and ASM International, Materials Park, OH, 1997, pp. 29-36.

119. “Use of the SEM in Failure Analysis,” Acta Microscopia, Proceedings of the XVI Meeting of the Brazilian Society for Electron Microscopy, Caxambu, Brazil, 1-5 September 1997, pp. 56-59.

120.”Measuring Second Phases by Image Analysis,” DGM Annual Meeting, Karlsruhe, Germany, 10-12 September 1997, pp. 45-54.

121. “Grain Size Estimation in Anisotropic Materials,” Metallurgical and Materials Transactions A, (with B.R. Morris and A. M. Gokhale). Vol. 29A, January 1998, pp. 237-244.

122. “Identifying the Cause of Tool and Die Failure, Stamping Q., Vol. 9, No. 5, Sept./Oct. 1997, pp. 34-36.

123. “Contemporary Concepts in Specimen Preparation” 10th Symposium on Metallography, Metallography „98, Stara Lesna, Poprad, Slovakia, April 22, 1998, pp. 3-6.

124. “The Science (and Art) of Metallography”, with Albert Brandemarte, ASTM Standardization News, Vol. 26, June 1998, pp. 27-31.

125. “Metallography of Superalloys”, Materials „98, Institute Materials Engineering Australasia, University of Woolongong, Australia, July 8, 1998, Vol. 2, pp. 407-414.

126. “New Metallographic Practices for Studying Heat Treated Metals and Alloys”, 1st International Conference on Automotive Heat Treating (ASMI), Puerto Vallarta, Mexico, July 15, 1998. (George Blann, co-author), ASM International, Materials Park, Ohio, 1999, pp. 358-363.

127. “Contemporary Concepts in Specimen Preparation” , IMS Meeting, 31st Annual Convention, Ottawa, Canada, July 29, 1998, Microstructural Science, Vol. 26, IMS and ASM International, Materials Park, OH, 1999, pp. 321-326.

128. “New Materials for Metallographic Specimen Preparation” , Internationale Metallographie - Tagung (DGM), Montanuniversitat Leoben, Leoben, Austria, Prakt. Met. Sonderband 30, 1999, pp. 17-28.

129. “Automating Microindentation Hardness Testing” , HARDMEKO „98 (Chinese Society for Measurement), Beijing, China, September 22, 1998, pp. 47-52. (Gabriel Lucas co-author).

130. “Binary Phase Diagrams and Microstructures, Materials Characterization, Vol. 41, No. 2, 1998, pp. 69-79.

131. “Revealing the Microstructure of Heat Treated Specimens,” 17th National Conf. on Heat Treatment, Brno, Czech Republic, 1998, pp. 37-44.

132. “Microindentation Hardness Testing,” Advanced Materials & Processes, Vol. 154, No. 3, September 1998, pp. 21,22, 24-25.

133. “Inclusion Measurement by ASTM E 1245,” CIM Bulletin, Vol. 91, No. 1021, June 1998, pp. 104-106.

134. “Metallographic Procedures for Cast Aluminum Alloys,” Modern Castings, Vol. , December 1998.

135. “The Basics of Cast Iron Metallography,” Modern Castings, Vol. 88, December 1998, pp. 46-47 (with J. Radzikowska, The Foundry Research Institute, Kraków, Poland).

136. “Metallography,” ASM Metals Handbook, Desk Edition, 2nd ed., ASM International, Materials Park, Ohio, December 1998, pp. 1356-1409.

137. Metallography: Principles and Practice, republished by ASM International, Materials Park, Ohio, 1999.

138. “Contemporary Concepts in Specimen Preparation,” Microstructural Science, Vol. 26, ASM Intl., Materials Park, Ohio, 1999, pp. 321-326.

139. “Automating Microindentation Hardness Testing,” 2nd National Conference, Metallography 1999, Ustrón, Poland, 21-23 April 1999, pp. 155-162 (G.M. Lucas, co-author).

140. “New Materials for Metallographic Specimen Preparation,” Prak.Met. Sonderband 30, 1999, pp. 17-28.

141. “Metallographic Techniques for Tool Steels,” Tool Steels in the Next Century, 5th International Conference on Tooling, F. Jeglitsch et al., editors, Montanuniversität Leoben, Leoben, Austria, 1999, pp. 415-424.

142. “Metallographic Preparation of Titanium and its Alloys,” 9th World Conference on Titanium, St. Petersburg, Russia, 7-11, 1999, Titanium ’99, I.V. Gorynin and S.S. Ushkov, eds., Vol. II, CRISM Prometey, St. Petersburg, Russia, 2000, pp. 828-834.

143. “Microindentation Hardness Testing,” Metals Handbook, Vol. 8, Mechanical Testing and Evaluation, ASM Intl., Materials Park, OH, 2000, pp. 221-231.

144. “Trends in Specimen Preparation,” Advanced Materials & Processes, Vol. 157, February 2000, pp. 45-49.

145. “Metallography for Edge Retention in Surface Treated Sintered Carbides and Steels,” Industrial Heating, March 2000, pp. 85-90.

146. “Copper Color Metallography,” Advanced Materials & Process,” Vol. 158, Number 1, July 2000, pp. 36-40.

147. “The Use of Light Microscopy in Failure Analysis,” Risk, Economy and Safety, Failure Minimisation and Analysis, R. K. Penny (ed.), Engineering Materials Advisory Services Ltd., West Lidlands, UK, 2000, pg. 135-150.

148. “Metallographic Techniques for Duplex Stainless Steels,” Proceedings of the 6th World Conference on Duplex Stainless Steels, Associazione Italiana di Metallurgia, Milano, Italy, 2000, p. 755-760.

149. “Metallographic Procedures for Edge Retention to Study Surface Hardening Processes,” Proc. 18th National Conf. on Heat Treatment, Association for Heat Treatment of Metals, Praha, Czech Republic, 2000, pp. 305-310.

150. “Microstructure of Ferrous Alloys,” Industrial Heating, Vol. 68, January 2001, pp. 28-34.

151. “Metallography of Iron Meteorites,” Advanced Materials & Processes, Vol. 159, February 2001, pp. 37-41.

152. “Conducting the Failure Examination,” Practical Failure Analysis, Vol. 1, No. 2, April 2001, pp. 14-19, 38-46.

153. “Introduction to Stereological Principles,” Practical Guide to Image Analysis, ASM International, Materials Park, OH, 2000, pp. 15-34.

154. “Specimen Preparation for Image Analysis,” Practical Guide to Image Analysis, ASM International, Materials Park, OH, 2000, pp. 35-74.

155. “Etching Isothermally Treated Steels,”Heat Treating Progress, Vol. 1, No. 2, April/May 2001, pp. 25-32.

156. “Metallographic Techniques for Duplex Stainless Steels,” Metallograpgy 2001, Stara Lesna, Slovakia, Acta Metallurgica Slovaca, Metallography ’01, Vol. 7, 2001, pp. 25-28.

157. Co-Editor, Special Issue on Stermat 2000: Stereology and Image Analysis in Materials Science, Materials Characterization, Vol. 46, Nos. 2/3, February/March 2001 (with B. Ralph, L. Wojnar and K.J. Kurzydlowski).

158. “Microstructure of Sintered Carbide Inserts, Seventh International Conference on the Science of Hard Materails, Ixtapa, Mexico, March 5-9, 2001, pp. 79-80.

159. “Microstructure of Isothermally Transformed Steels,” Metal 2001, Ostrava, Czech Republic, published on CD, paper 195.

160. “Identification of Phases in Stainless Steels by Selective Etching,” Metal 2001, Ostrava, Czech Republic, published on CD, paper 194.

161. “Anisotropy Estimation Properties for Microstructural Models,” Materials Characterization, Vol. 46, 2001, pp. 93-98 (with V. Beneš, M. Hlawiczková and A. M. Gokhale).

162. “Metallographic Procedures for Precious Metals,” Euromat 2001, Rimini, Italy, p. 208 (paper on CD).

163. “Metallography of Magnesium Die-Cast Alloys,” Proc. High Tech Diecasting (Al and Mg Alloys),” Associazione Italiana Di Metallurgia, Milano, 2002, pp. 43-51.

164. “Ferrous Metallography,” Analytical Characterization of Aluminum, Steel and Superalloys, D.S Mackenzie and G.E. Totten, eds., CRC Press, Taylor & Francis Group, Boca Raton, Florida, 2006, pp. 1-53.

165. “Atlas of Aluminum Microstructures,” Analytical Characterization of Aluminum, Steel, and Superalloys, D.S. Mackenzie and G.E. Totten, eds, CRC Press, Taylor & Francis Group, Boca Raton, Florida, 2006, pp. 55-156

166. “Color Metallography,” Proc. of the 2002 M&M Meeting, Quebec City, Quebec, Canada, August 2002 (CD).

167. “Walter Mannheimer is 2002 Sorby Winner,” Slip Lines, Vol. 30, June 2002, p. 1and 7.

168. “My Friend, Leonard E. Samuels,” Slip Lines, Vol. 30, June 2002, p. 3 and 7.

169. “IMS in Québec City,” Slip Lines, Vol. 30, September 2002, p. 1 and 3.

170. “IMS 2003 Meets with M&M 2003 in San Antonio, August 3-7, 2003,” Slip Lines, Vol. 30, December 2002, p. 1 and 7.

171. Buehler’s Guide to Materials Preparation, Buehler Ltd, Lake Bluff, Illinois, 2002, 128 pgs.

172. “Metallographic Techniques in Failure Analysis,” Metals Handbook, Vol. 11, Failure Analysis and Prevention, ASM International, Materials Park, OH, 2002, pp. 498-515.

173. “Conducting a Failure Examination,” Metals Handbook, Vol. 11, Failure Analysis and Prevention, ASM International, Materials Park, OH, 2002, pp. 333-342.

174. “Ferrous Metallography,” D.S. Mackenzie and G.E. Totten, eds., Analytical Characterization of Aluminum, Steel, and Superalloys, CRC Press Taylor & Francis Group, 2006, pp. 1-53.

175. “Atlas of Aluminum Microstructures,” D.S. Mackenzie and G.E. Totten, eds., Analytical Characterization of Aluminum, Steel, and Superalloys, CRC Press Taylor & Francis Group, 2006, pp. 55-156.

176. “Microstructure of Ferrous Alloys,” D.S. Mackenzie and G.E. Totten, eds., Analytical Characterization of Aluminum, Steel, and Superalloys, CRC Press Taylor & Francis Group, 2006, pp.157-234.

177. “Metallography of Mg Die cast Alloys,” Metallurgiia Italiana, Vol. 94, October 2002, pp. 37-41.

178. “The Use of Color Metallographic Techniques to Study Welds, Proc. Microscopy & Microanalysis 2003, Vol. 9, Suppl. 2, 2003, paper 702CD.

179. “Metallographic Procedures for Cast Iron,” Proc. XV Foundry Industrial Conf., published on conference CD, paper number 3.

180. “Failure Analysis of Tools and Dies,” ASM Specialty Handbook, Tool Materials, ASM International, Materials Park, OH, 1995, pp. 421-442.

181. “Microscopy & Microanalysis 2003,” Advanced Materials & Processes, Vol. 167, No. 7, July 2003, pp. 44-45.

182. “Metallography of Superalloys,” Industrial Heating, Vol. 70, October 2003, pp. 40-43.

183. “Use of Color Etching to Study Historic Artifacts,” Proc. Archeometallurgy in Europe, Vol. 2, Associazione Italiana di Metallurgia, Milan, 2003, pp. 369-377.

184. “Prof. Enrica Stagno of Genoa University to Receive Henry Clifton Sorby Award,” Slip Lines, Vol. 31, No. 2, June 2003, p. 1.

185. “Metallography: Standards, Fundamentals and New Directions,” Microscopy & Microanalysis 2003, San Antonio, Texas, August 3-7,” Slip Lines, Vol. 31, No. 2, June 2003, p. 4.

186. “IMS 2003 in San Antonio,” Slip Lines, Vol. 31, No. 3, September 2003, pp. 1 and 4.

187. “Metallography,” Chapter 10 in Smithells Metals Reference Book, 8th ed., W.F. Gale and T.C. Totemeier, eds., Elsevier Buttereorth-Heinemann (and ASM International), Oxford, 2004, pp. 10-1 to 10-87.

188. “Metallography of Titanium and Its Alloys,” Current Advances in Mechanical Design and Production, VIII, Vol. III, A. M. Metwalli et al., eds., MDP-8 Cairo University Conference, Cairo University, 2004, pp. 79-85.

189. “Investigation of Carbides in Gas Turbine Disks Produced from EP428 Grade Steel After Long-Term Service Exposure,” Materials Characterization, Vol. 52, No. 1, pp. 27-34 (E.P. Manilova primary author).

190. “Metallographic Examination of Heavily Eroded Structural Steel from World Trade Center Buildings 1, 2 and 7,” Submitted to Materials Characterization (R.R. Biederman, E. Sullivan, GFV, and R.D. Sisson).

191. “Color Metallography,” Proceedings Microscopy & Microanalysis 2004, I.M. Anderson et al., editors, Press Syndicate of the University of Cambridge, Cambridge, England, 2004, pp. 70-71.

192. “Welding Metallography – Ferrous Metals,” Acta Metallurgica Slovaca, Special Issue 1/2004, Proceedings of Metallography 2004, M. Longauerová et al.,  editors, 2004, pp. 66-74.

193. “Metallographic Techniques for Superalloys,” Proceedings Microscopy & Microanalysis 2004, I.M. Anderson et al., editors, Press Syndicate of the University of Cambridge, Cambridge, England, 2004, paper 690 on conf. CD (E.P. Manilova co-author).

194. “A Study of Selective Etching of Carbides in Steel,” Proceedings Microscopy & Microanalysis 2004, I.M. Anderson et al., editors, Press Syndicate of the University of Cambridge, Cambridge, England, 2004, pp. 76-77  (E.P. Manilova and J. R. Michael co-authors).

195. “The Reflected Light Metallurgical Microscope,” Encyclopedia of Condensed Matter Physics, Elsevier Ltd, Oxford, 2004.

196. “See Things More Clearly With Micrographs,” Advanced Materials & Progress, Vol. 162, No. 2, February 2004, p. 57.

197. “Metallographic Examination of Heavily Eroded Structural Steel from World Trade Center Buildings 1, 2 and 7,” Risk, Economy and Safety, Failure Minimisation and Analysis, Proceedings of Failures 2004, R.K. Penny, ed., EMAS Publishing Ltd., Sheffield, UK, 2004, pp. 225-234  (R.R. Biederman, E. Sullivan, GFV, and R.D. Sisson).

198. Volume editor, Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 1184 pgs., 2004.

199. “Metallographic Preparation of Orthopedic Medical Devices,” Medical Device Materials II, ASM International, Materials Park, OH, 2005, pp.  75-80 (D. Medlin and G. Lucas co-authors).

200. “Polarized Light Microscopy: Utilization in the Investigation of the Recrystallization of Aluminum Alloys,” Materials Characterization, Vol. 52, No. 3, June 2004, pp. 165-177 (M. Slámová, V. Očenášek and GFV).

201. “Study of Selective Etching of Carbides in Steel,” 38th Metallographie Tagung mit Ausstellung, Fortschritte in der Metallographie. 36, Sonderbande der Praktischie Metallographie 36, Deutsche Gesellschaft für Materialkunde e.V., Frankfurt, Germany, 2004, pp. 255-260 (co-authors: E.P. Manilova, J.R. Michael and G. M. Lucas).

202. “A Study of Selective Etching of Carbides in Steel,” 9th Micromat – Brazilian Symposium on Materials Microscopy, Foz do Iguacu, Brasil, published on conference CD (co-authors: E.P. Manilova and J.R. Michael).

203. “Metallographic Characterization of the Microstructure of Tool Steels,” Transactions of Materials and Heat Treatment, Vol. 25, No. 4, Proceedings of the 14th Congress of International Federation for Heat Treatment and Surface Engineering, Shanghai, China, pp. 169-173 (E.P. Manilova co-author).

204. “Investigation of Carbides in Gas Turbine Disks Produced from EP428 Grade Steel after Long-Term Service Exposure,” 3a Jornadas Internacionales De Materialografia Y Caracterization Microstructural, INASMET 2004, Grupo Delta, San Sebastian, Spain, 2004, pp. 63-73 (E.P. Manilova co-author).

205. “Color Metallography,” 3a Jornadas Internacionales De Materialografia Y Caracterization Microstructural, INASMET 2004, Grupo Delta, San Sebastian, Spain, 2004, pp. 77-86.

206. “Metallography and Microstructure of Aluminum and Alloys,” 3a Jornadas Internacionales De Materialografia Y Caracterization Microstructural, INASMET 2004, Grupo Delta, San Sebastian, Spain, 2004, pp. 89-97 (E.P. Manilova co-author).

207. “Light Microscopy,” Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 2004, pp. 332-354.

208. “Color Metallography,” Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 2004, pp. 493-512

209. “Microstructure and Domain Imaging of Magnetic Materials,” Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 2004, pp. 969-993 (M.A. Williard co-author).

210. “Metallography and Microstructures of Stainless Steels and Maraging Steels,” Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 2004, pp. 670-700 (G.M. Lucas and E.P. Manilova co-authors).

211. “Metallography and Microstructures of Heat-Resisting Alloys,” Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 2004, pp. 820-859 (G.M. Lucas and E.P. Manilova co-authors).

212. “Metallographic Techniques for Tool Steels,” Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 2004, pp. 644-669.

213. “Laboratory Safety in Metallography,” Metallography and Microstructures, Volume 9, ASM Handbook series, ASM International, Materials Park, Ohio, 2004, pp. 1081-1089.

214., “Metalografická Příprava Hliníkových Slitin (Metallographic Preparation of Aluminum Alloys),” in Encyklopedie Hliníku, Stefan Michna et al., eds., Adin, s.r.o., Prešov, Czech Republic, 2005, pp. 411-422 (E. P. Manilova, co-author).

215. “Hints for Imaging Phases in Steels,” Advanced Materials & Processes, Vol. 163, No. 2, February 2005, pp. 32-37 (E. P. Manilova co-author).

216. “Aloha! IMS in Hawaii,” Slip Lines, Vol. 33, Issue 1, January 2005, pps. 1, 4-7.

217. “IMS 2005: An Extraordinary Convention,” Slip Lines, Vol. 33, Issue 2, March 2005, p. 6.

218. “Metallographic Examination of Sintered Carbides,” 10th Konference, Přímos Metalografie Pro Řešení Výrobních Problémů, Láznĕ Libverda, Czech Republic, 2005, p. 70.

219. “Interlaboratory Program to Characterize Discrete Second-Phase Particles by Image Analysis,” Microscopy & Microanalysis 2005, Honolulu, conference CD.

220. “Microstructure of Powder Metallurgy Components,” Microscopy & Microanalysis 2005, Honolulu, conference CD.

221. “IMS in Hawaii: A Metallographer’s Guide to Oahu,” Slip Lines, Vol. 33, No. 3, June 2005, p. 1, 4, 5 (E. P. Manilova, co-author).

222. “International Metallographic Society Convention,” Advanced Materials & Proceses, Vol. 163, No. 6, June 2005, p. 66.

223. “IMS in Hawaii: A Spectacular Conference!,” Slip Lines, Vol. 33, No. 4, November 2005, p. 1, 4, 5.

224. “Color Metallography,” Microscopy Today, Vol. 13, No. 6, November 2005, pp. 22-27.

225. “Microstructural Optimization of Chill Cast Al-Si Eutectic Alloys,” Proc. Microscopy and Microanalysis 2006, P. Kotula et. al, eds., Cambridge University Press, 2006, 1608 CD (J. Asensio-Lozano and B. Suá rez-Peña co-authors)

226. “Metallographic Preparation for Electron Backscattered Diffraction,” Proc. Microscopy and Microanalysis 2006, P. Kotula et. al, eds., Cambridge University Press, 2006, 1610CD (W. Van Geertruyden, S. Dillon and E. Manilova co-authors).

227. “Metallography and Microstructure of Metals Used in Medical Devices,” Proc. Microscopy and Microanalysis 2006, P. Kotula et. al, eds., Cambridge University Press, 2006, 1618 CD.

228. Microstructure of Titanium and Its Alloys,” Industrial Heating, Vol. 73, June 2006, pp. 77-80, 82-84.

229. “Metallographic Preparation for Electron Backscattered Diffraction,” Metallography 2007, Acta Metallurgica Slovaca, 3/2007, M. Longaurová et. al, eds., pp. 33-37.

230. “Interpretation of the Mechanical Quality Index through the Microstructure and Eutectic Treated Al-Si Alloys, Proceedings of 65th Annual Microscopy & Microanalysis Conference, August 5-9, 2007, p. 110-111 (J. Asensio –Lozano and B. Suarez)

231. “Metallographic Research on the Pressure Effect on the Final Microstructure of Eutectic Al-Si Alloys,” Proceedings of 65th Annual Microscopy & Microanalysis Conference, August 5-9, 2007, 1030CD (B. Suarez and J. Asensio-Lozano)

232. “Microstructure of Historic Bronze Objects,” Proceedings of 65th Annual Microscopy & Microanalysis Conference, August 5-9, 2007, 1110CD.

233. “Metallographic Examination of Medical Implants,” Fortschritte in der Metallographie, No. 39, Proc. Of 2007 DGM Tagung, 19-21 2007, in Bremen, Germany, Werkstoff-Informationsgesellschaft mbH, Frankfurt, Germany, 2007, pp. 45-54 (co-authors: G. M. Lucas and E.P. Manilova).

234. “Metallographic Preparation for Electron Backscatter Diffraction,” McGraw-Hill Yearbook of Science & Technology, 2008, McGraw-Hill Book Co., NY, 2008, pps.202-206 (E.P. Manilova, co-author).

235. “Specimen Preparation for Electron Backscattered Diffraction (EBSD),” 95 MB Word document, CD made by Buehler for distribution, 2007.

236. “Titanium Specimen Preparation,” Advanced Materials & Processes, February 2008, Vol. 166, No. 2, pp. 25-27.

237. “Metallographic Preparation for Electron Backscattered Diffraction,” Proc. 5th International Conference on Materialography and Microstructural Characterization, San Sebastian, Spain, 2008, pp. 81-88.

238.  “Characterization of Q & T Steel Poleshoes Manufactured by Sand Casting,” Practical Metallography, Vol. 45, No. 4, 2008, pp. 182-197 (J. Asensio-Lozano, J.F. Alvarez-Antolin, J.T. Panta-Mesones and GFV).

239. “Examination of Sectioning Damage by EBSD,” Proc. Microscopy & Microanalysis 2008, Conference CD (with Gabe Lucas).

240. “Delineation and Measurement of Grain Size by EBSD,” Proceedings Microscopy & Microanalysis 2008, conference CD (with E.P. Vander Voort, M. Nowell).

241. “Microstructural Control of FeB-Inoculated Mottled Low-Alloy White Iron by a Design of Experiments Approach,” Intl. Journal of Materials Research, Vol. 99, November 2008, pp. 1237-1247 (authors: J. Asensio, J.F. Alvarez and GFV).

242. “Identification and Quantification of Active Manufacturing Factors for Graphite Formation in Centrifugally Cast Nihard Cast Irons,” J. Materials Processing Technology, Vol. 206, 2008, pp. 202-215 (authors: J. Asensio-Lozano, J.F. Álvarez-Antolín and GFV).

243. “Prefect Prep.,” Ceramic Industry, Vol. , February 2009, pp. 14-17 (plus cover).

244. “Martensite and Retained Austenite,” Industrial Heating, Vol.76, April 2009, pp. 51-54.

245. “Specimen Preparation for Metallographic Examination of Medical Devices,” Advanced Materials & Processes, Vol. 176, No. 4, April 2009, p. 51.

246. “Metallographic Sectioning and Grinding Damage Analysis Through the Use of Color Metallography and Electron Backscattered Diffraction (EBSD),” Proceedings Microscopy and Microanalysis 2009, Vol. 15, Supplement 2, 2009, Cambridge University Press, Cambridge, UK, pp. 58-59 (co-authors: G.M. Lucas, P.T. Pinard, M. Lagace and P. Hovington).

247. “The Al – Si Phase Diagram, Proceedings Microscopy and Microanalysis 2009, Vol. 15, Supplement 2, 2009, Cambridge University Press, Cambridge, UK, pp. 60-61 (co-author: J.Asensio-Lozano).

248. Quantitative Evaluation of Metallographic Preparation Quality Using EBSD,” Proceedings Microscopy and Microanalysis 2009, Vol. 15, Supplement 2, 2009, Cambridge University Press, Cambridge, UK,  Conference CD # 778  (co-authors: P.T. Pinard, P. Hovington, M. Lagacé G.M. Lucas and R. Gauvin).

249. “Metallographic Examination of Bronze Bracelets from Hasanlu,” Proceedings Microscopy and Microanalysis 2009, Vol. 15, Supplement 2, 2009, Cambridge University Press, Cambridge, UK, Conference CD #1516.

250. “Characterization of Carburized Steel Microstructures,” Heat Treat Progress, October 2009, pp 37-42 (G.M. Lucas, co-author).

251. “Metallographic Specimen Preparation for Electron backscatter Diffraction, La Metallurgia Italiano, Vol. 101, November - December 2009, pp 71-79.

252. “Revealing Prior-Austenite Grain Boundaries in Heat-Treated Steels,” Industrial Heating, Vol. 78, April 2010, pp. 48-52.

253. “From Crankshafts to Bore Cores,” Practical Metallography, June 2010, pp. 313-341 (with Barry Jenkins).

254. Revealing Prior-Austenite Grain Boundaries,” Paper 250, Microscopy & Microanalysis 2010, Portland, Ohio, August 3, 2010, conference CD.

255. "Influence of Specimen Preparation on SEM Images and Comparison to LOM Images, Paper 540, Microscopy & Microanalysis 2010, Portland, Ohio, August 4, 2010, conference CD.

256.”Towards a More Quantitative Measurement of the Deformation During Metallographic Specimen Preparation Using EBSD and FIB,” Paper 649, Microscopy & Microanalysis 2010, Portland, Ohio, August 4, 2010, conference CD (authors: P.T. Pinard, M. Lagace and G.F. Vander Voort).

257. “Metallography of Welds,” Advanced Materials & Processes, Vol. 169, June 2011, pp. 19-23.

258. “Picric Acid: Hazards and Safe Usage,” Industrial Heating, Vol. 79, June 2011, p. 28.

259. “Obtaining Consistent Vickers Hardness at Loads ≤100 Grams Force,” Microscopy & Microanalysis 2011, Nashville, Conference Proceedings and CD (#302), with Ryan Fowler.

260. “Methanol Pipeline Failure in the Canyon Express System,” Microscopy & Microanalysis 2011, Nashville, Conference Proceedings and CD (#627), with G. Lucas.

261. “Specimen Preparation of Metals and Alloys for EBSD,” Microscopy & Microanalysis 2011, Nashville, Conference Proceedings and CD (#911), with P. Pinard.

262. “Metallographic Specimen Preparation for Electron Backscattered Diffraction - Part1,” Practical Metallography, Vol. 48, No. 9, September 2011, pp. 454-473.

263. “Metallographic Specimen Preparation for Electron Backscattered Diffraction – Part 2,” Practical Metallography, Vol. 48, No.10, October 2011, pp. 527-543.

264. “Microstructure of Nitrided Steels,” Industrial Heating,” Vol. 79, November 2011, pp. 51-55.

265. “Low-Load Vickers Microindentation Hardness Testing,” Advanced Materials & Processes, Vol. 170, No. 4, April 2012, pp. 28-33 (with Ryan Fowler).

266. “The Lampshade Frame: A Study of Provenance,” Advanced Materials & Processes, Vol. 170, No. 8, August 2012, pp. 15-19.

267. “Color Metallography,” Industrial Heating, Vol. 80, No. 8, August 2012, pp. 53-54, 56.

268. “Metallography of Fe and Steel Alloys,” Encyclopedia of Iron, Steel and their Alloys, Taylor & Francis Group, Rafael Colás and George E. Totten, editors-in-chief, to be published.

269. “Determination of the Degree of Thermal Exposure to the Lower Head of the Three-Mile Island Unit 2 Nuclear Reactor Using Metallography,” Proceedings of Ferrous 2012: Ferrous and Base Metals Development Network Conference, 15-17 October 2012, South African Institute of Mining and Metallurgy, Johannesburg, Symposium Series S73, Camera Press, 2012, pp. 353-367.

270. “Grain Size Measurements Using Circular or Rectangular Test Grids,” Practical Metallography, Vol. 50, No. 1, January 2013, pp. 17-31.

271.”Determination of the Degree of Thermal Exposure to the Lower Head of the Three-Mile Island Unit 2 Nuclear Reactor Using Metallography,” J. of the Southern African Institute of Mining and Metallurgy, Vol. 113, February 2013, pp. 137-142.

272. “Microstructural Investigations of Streak Formatiom in 6063 Aluminum Extrusions by Optical Metallographic Techniques,” Microscopy & Microanalysis, Vol. 19, No. 2, Apil 2013, pp. 276-284 (co-authors: B. Suárez-Peña and Juan Asensio-Lozano).

273. Guest Editorial, 50th Anniversary of Practical Metallography/Praktische Metallographie, Vol. 50, No. 4, April 2013, pp. 235-238.

274. “Measuring the Grain Size of Specimens with Non-Equiaxed Grains,” Practical Metallography, Vol. 50, No. 4, April 2013, pp. 239-251.

275. “Interview with Guest Editor George Vander Voort,” Practical Metallography, Vol. 50, No. 4, April 2013, pp. 290-294.

276. “Color Metallography and Electron Microscopy Techniques Applied to the Characterization of 413.0 Aluminum Alloys,” Microscopy and Microanalysis, Microscopy and Microanalysis, Vol. 19, No. 4, August 2013, pp. 1019-1026 (Juan Asensio-Lozano and Beatriz Suárez-Peña co-authors). (Color micrograph on cover of issue).

277. “Metallographic Characterization of Carburized Steels,” Proceedings of the IFHTSE and ASMI Heat Treating and Surface Engineering Expo, Chennai Trade Centre, Chennai, India, TBP.

278. “Determination of the Degree of Thermal Exposure to the Lower Head of the Three-Mile Island Unit 2 Nuclear Reactor Using Metallography,” Advanced Metal, Materials and Technologies, 10th International Scientific and Technical Conference, St. Petersburg, Russia, 25 June 2013, Conference Proceedings, pgs. 129-130.

279. “Is there Possible Bias in ASTM E112 Planimetric Grain Size Measurements?” Materials Performance and Characterization, Vol. 2, No. 1, 2013, pp. 194-205.

Blogs in Industrial Heating Magazine and on their Web Site

1. “Picric Acid – Hazards and Safe Useage,” May 6, 2011.

2. “Identification of Phases in Stainless Steels by Selective Etching (Part  1)”, July 14, 2011

3. Identification of Phases in Stainless Steels by Selective Etching (Part 2),” July 21, 2011

4. “Study of Selective Etching of Carbides in Steel (Part1),” August 15, 2011

5. “Study of Selective Etching of Carbides in Steel (Part 2),” September 1, 2011

6. “Bias in Grain-Size Chart Ratings,” October 3, 2011

7. “Revealing Prior-Austenite Grain Boundaries by Etching,” November 3, 2011

8. “Use of Color Metallographic Techniques to Study Welds (Part 1),” November 18, 2011

9. “Use of Color Metallographic Techniques to Study Welds (Part 2),” December 2, 2011

10. “Microstructure of Nitrided Steels (Part 1),” December 20, 2011

11. “Microstructure of Nitrided Steels (Part 2),” January 12, 2012

12. “Metallography of Surface Treatments, Coatings and Platings (Part 1),” March 12, 2012

13. “Metallography of Surface Treatments, Coatings and Platings (Part 2),” March 26, 2012

14. “Introduction to Quantitative Metallography (Part 1),” May 7, 2012

15. “Introduction to Quantitative Metallography (Part 2),” May 18, 2012

16. “Introduction to Quantitative Metallography (Part 3),” June 11, 2012

17. “Introduction to Quantitative Metallography (Part 4),” July 2, 2012

18. “Introduction to Quantitative Metallography (Part 5),” August 3, 2012

19. “Color Metallography (Part 1),” January 7, 2013

20. “Color Metallography (Part 1),” February 18, 2013

21. “Color Tint Etching (Part 1),” March 18, 2013

22. “Color Tint Etching (Part 2),” May 5, 2013

Articles on Vac Aero Website

1. “Metallographic Specimen Preparation for Electron Backscattered Diffraction”

2. “Microstructure of Isothermally-Treated Steels”

3. “Picric Acid – Hazards and Safe Useage”

4. “Identification of Phases in Stainless Steels by Etching,” (in 2 Parts)

5. “A Layman’s View of Plasma Coating Metallography”

6. “Color Metallography”

7. “Metallography of Surface Treatments and Coatings”

8. “Microstructure of Ferrous Alloys”

9. “Metallography of Superalloys”

10. “Revealing Prior-Austenite Grain Boundaries in Heat-Treated Steels”

11. Materials Characterization and Testing: Microstructure of Titanium and Its Alloys”

12. “Martensite and Retained Austenite”

13. “Microstructure of Nitrided Steels”

14. “Introduction to Quantitative Metallography”

15. “Metallographic Preparation of Tool Steels”

16. “Revealing the Microstructure of Tool Steels”

17. “Introduction to Stereological Principles”

18. “Study of Selective Etching of Carbides in Steel”

19. “Metallography and Microstructure of Aluminum and Its Alloys”

20. “Bias in Grain Size Chart Ratings”

21. “The Value of Color Metallographic Techniques in the Study of Welds”

22. “Metallographic Procedures for Precious Metals”

23. “Measurement of Grain Shape Uniformity”

24. “Measurement of Grain Size in Twinned FCC Alloys”

25.”Grain Size Measurement: The Jeffries Planimetric Method”

26.” Grain Size Measurement: The Heyn Intercept Method”

27. Grain Size Measurement: The Saltykov Rectangle

28. “Measuring the Grain Size of Specimens with Deformed Grains”

29. “Grain Size Measurements by the Triple Point Count Method”

30. “Metallography of Iron-Nickel Meteorites – Part I: Background”

31. “Measuring Inclusion Content by ASTM E 1245”

32. “Methanol Pipeline Failure in the Canyon Express Pipeline System”

33. “Metallography of Iron-Nickel Meteorites – Part II: Phases”

34. “Decarburization”

35. “Metallography of Iron-Nickel Meteorites – Part III: Microstructure in Color”

36. “Obtaining Consistent Vickers hardness at Loads 100 Grams Force”

37. “Metallographic Examination of Bronze Bracelets from Hasanlu”

38. "Propeller Shaft of the USS Monitor"

Buehler Tech-Notes:

1. “Fastener Metallography for Today!,” Vol. 1, No. 1, April 1997 (Jim Nelson).

2. “Preparation of Thermally Sprayed Coatings!,” Vol. 1, No. 2, May 1997 (George Blann).

3. “The World Beyond Brightfield Illumination!,” Vol. 1, No. 3, June 1997 (GFV only).

4. “Image Processing in the Material?s Laboratory,” Vol. 1, No. 4, July 1997 (Matt Hoffmann and Kai Akatsu).

5. “Introduction to Quantitative Metallography,” Vol. 1, No. 5, August 1997 (GFV only).

6. “Microindentation Hardness Testing,” Vol. 1, No. 6, September 1997 (Janice Kamm).

7. “Microsectioning for Soldered Connection Analysis,” Vol. 1, No. 7, October 1997 (Jim Nelson).

8. “Contemporary Concepts in Specimen Preparation,” Vol. 1, No.8, December 1997 (with George Blann).

9. “Which Hot Mounting Compound Should I Use?”, Vol. 2, No. 1, 1998.

10. “Preparation of Cast Iron Foundry Alloys,” Vol. 2, No. 2, 1998 (Janina Radzikowska).

11. “PLANARMET AL Paper for Rough Grinding,” Vol. 2, No. 3, 1998 (with Gabe Lucas).

12. “Quantitative Image Analysis, Part I Principles,” Vol. 2, No. 4, 1998 (Dennis Hetzner).

13. “Metallography of Precious Metals for Jewelry,” Vol. 2, No. 5, 1998 (Jeff Stewart).

14. “Microelectronics, Part I: Cutting, Mounting,” Vol. 3, No. 1, 1999 (Scott Holt).

15. “Preparation of Cast Aluminum-Silicon Alloys,” Vol. 3, No. 2, 1999.

16. “Preparation of Titanium and its Alloys,” Vol. 3, No. 3, 1999.

17. “Orbital Technology – The Science of the Cut,” Vol. 3, No. 4, 2000 (S. Buttitta and N. Dougill).

18. “Petrographic Examination Methods,” Vol. 3, No. 5, 2000 (W. Ahmed).

19. “Microstructure of Iron-Based Alloys,” Vol. 4, No. 1, 2003.

20. “Metallography of Magnesium and its Alloys, Vol. 4, No. 2, 2004

21. “Welding Metallography – Ferrous Metals,” Vol. 4, No. 3, 2004

22. “Resin/Diamond Surfaces Enhance Microstructutural Analysis of Thermally Sprayed Coatings, Vol. 4, No. 4,

2004

23. “Preparation of Intravascular Stent Thin Sections,” Vol. 4, No. 5, 2004

24. “The Al-Si Phase Diagram,” Vol. 5, No. 1, 2008 (with Juan Asensio-Lozano).

25. “Specimen Preparation for Electron Backscattered Diffraction,” Vol. 5, No. 2, 2008.

26. “Metallographic Preparation of Tool Steels,” Vol. 5, No. 3, 2008.

Posters for Buehler:

1. Specimen Preparation for EBSD,

2. The Pb-Sn Phase Diagram, October 2009

3. The Al-Si Phase Diagram, October 2009

4. EBSD of High-Purity Metals, November 2009

Non-Technical Publications

1. "Hiking in Norway - What You Need To Know," International Travel News, Vol. 20, No. 4, June 1995, pp. 55-62.

2. "Norway's Hut Network Offers Hikers Plenty of Options," International Travel News, Vol. 20, No. 5, July 1995, pp. 35-39.

3. “Touring and Tasting in Argentina’s Medoza Wine Region,” International Travel News, Vol. 35, No. 7,       September 2010, pp. 34-39

Log in to your account or